|
ASTM A 1008/A 1008M REV B |
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable |
|
ASTM A 105/A 105M |
Standard Specification for Carbon Steel Forgings for Piping Applications |
|
ASTM A 106/A 106M REV B |
Standard Specification for Seamless Carbon Steel Pipe for High- Temperature Service |
|
ASTM A 108 |
Standard Specification for Steel Bar, Carbon and Alloy, Cold- Finished |
|
ASTM A 109/A 109M |
Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled |
|
ASTM A 123/A 123M |
Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products |
|
ASTM A 126 |
Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings |
|
ASTM A 131/A 131M REV A |
Standard Specification for Structural Steel for Ships |
|
ASTM A 148/A 148M |
Standard Specification for Steel Castings, High Strength, for Structural Purposes |
|
ASTM A 153/A 153M |
Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware-AASHTO No.: M232 |
|
ASTM A 167 |
Standard Specification for Stainless and Heat-Resisting Chromium- Nickel Steel Plate, Sheet, and Strip |
|
ASTM A 176 |
Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip |
|
ASTM A 181/A 181M |
Standard Specification for Carbon Steel Forgings, for General- Purpose Piping |
|
ASTM A 182/A 182M REV A |
Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service |
|
ASTM A 185/A 185M REV A |
Standard Specification for Steel Welded Wire Reinforcement, Plain, for Concrete |
|
ASTM A 194/A 194M REV B |
Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both |
|
ASTM A 20/A 20M |
Standard Specification for General Requirements for Steel Plates for Pressure Vessels |
|
ASTM A 213/A 213M REV C |
Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes |
|
ASTM A 216/A 216M |
Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service |
|
ASTM A 217/A 217M |
Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service |
|
ASTM A 228/A 228M |
Standard Specification for Steel Wire, Music Spring Quality |
|
ASTM A 234/A 234M REV A |
Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service |
|
ASTM A 240/A 240M REV A |
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
|
ASTM A 242/A 242M |
Standard Specification for High-Strength Low-Alloy Structural Steel- AASHTO No.: M 161 |
|
ASTM A 249/A 249M REV A |
Standard Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes |
|
ASTM A 262 REV A |
Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
|
ASTM A 266/A 266M REV A |
Standard Specification for Carbon Steel Forgings for Pressure Vessel Components |
|
ASTM A 268/A 268M REV A |
Standard Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service |
|
ASTM A 269 |
Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service |
|
ASTM A 27/A 27M |
Standard Specification for Steel Castings, Carbon, for General Application |
|
ASTM A 276 REV A |
Standard Specification for Stainless Steel Bars and Shapes |
|
ASTM A 283/A 283M |
Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates |
|
ASTM A 285/A 285M |
Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength |
|
ASTM A 29/A 29M |
Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for |
|
ASTM A 304 |
Standard Specification for Carbon and Alloy Steel Bars Subject to End- Quench Hardenability Requirements |
|
ASTM A 307 |
Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength |
|
ASTM A 312/A 312M REV A |
Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
|
ASTM A 313/A 313M |
Standard Specification for Stainless Steel Spring Wire |
|
ASTM A 314 |
Standard Specification for Stainless Steel Billets and Bars for Forging |
|
ASTM A 320/A 320M REV A |
Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for Low-Temperature Service |
|
ASTM A 322 |
Standard Specification for Steel Bars, Alloy, Standard Grades |
|
ASTM A 325 REV B |
Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength-AASHTO No.: M 164 |
|
ASTM A 333/A 333M |
Standard Specification for Seamless and Welded Steel Pipe for Low- Temperature Service |
|
ASTM A 335/A 335M REV A |
Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High- Temperature Service |
|
ASTM A 336/A 336M |
Standard Specification for Alloy Steel Forgings for Pressure and High- Temperature Parts |
|
ASTM A 350/A 350M REV A |
Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components |
|
ASTM A 351/A 351M |
Standard Specification for Castings, Austenitic, for Pressure- Containing Parts |
|
ASTM A 352/A 352M |
Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature Service |
|
ASTM A 354 |
Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners |
|
ASTM A 36/A 36M |
Standard Specification for Carbon Structural Steel |
|
ASTM A 370 |
Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
|
ASTM A 380 |
Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
|
ASTM A 387/A 387M REV A |
Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum |
|
ASTM A 395/A 395M |
Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
|
ASTM A 400 |
Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical Properties |
|
ASTM A 403/A 403M |
Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings |
|
ASTM A 434 |
Standard Specification for Steel Bars, Alloy, Hot-Wrought or Cold- Finished, Quenched and Tempered |
|
ASTM A 449 REV B |
Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/ 105/90 ksi Minimum Tensile Strength, General Use |
|
ASTM A 450/A 450M REV A |
Standard Specification for General Requirements for Carbon, Ferritic Alloy, and Austenitic Alloy Steel Tubes |
|
ASTM A 453/A 453M |
Standard Specification for High-Temperature Bolting Materials, with Expansion Coefficients Comparable to Austenitic Stainless Steels |
|
ASTM A 473 |
Standard Specification for Stainless Steel Forgings |
|
ASTM A 479/A 479M REV A |
Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels |
|
ASTM A 48/A 48M |
Standard Specification for Gray Iron Castings |
|
ASTM A 480/A 480M |
Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip |
|
ASTM A 487/A 487M |
Standard Specification for Steel Castings Suitable for Pressure Service |
|
ASTM A 490 REV A |
Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength-AASHTO No.: M 253 |
|
ASTM A 493 |
Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging |
|
ASTM A 500 REV A |
Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes |
|
ASTM A 501 |
Standard Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing |
|
ASTM A 510 |
Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel |
|
ASTM A 511 |
Standard Specification for Seamless Stainless Steel Mechanical Tubing |
|
ASTM A 513 |
Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing |
|
ASTM A 515/A 515M |
Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service |
|
ASTM A 516/A 516M |
Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
|
ASTM A 519 |
Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing |
|
ASTM A 53/A 53M |
Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc- Coated, Welded and Seamless |
|
ASTM A 530/A 530M REV A |
Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe |
|
ASTM A 536 |
Standard Specification for Ductile Iron Castings |
|
ASTM A 537/A 537M |
Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel |
|
ASTM A 554 |
Standard Specification for Welded Stainless Steel Mechanical Tubing |
|
ASTM A 563 REV A |
Standard Specification for Carbon and Alloy Steel Nuts |
|
ASTM A 564/A 564M |
Standard Specification for Hot-Rolled and Cold-Finished Age- Hardening Stainless Steel Bars and Shapes |
|
ASTM A 568/A 568M REV A |
Standard Specification for Steel, Sheet, Carbon, Structural, and High- Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for |
|
ASTM A 572/A 572M |
Standard Specification for High-Strength Low-Alloy Columbium- Vanadium Structural Steel-AASHTO No.: M223 |
|
ASTM A 574 |
Standard Specification for Alloy Steel Socket-Head Cap Screws |
|
ASTM A 575 |
Standard Specification for Steel Bars, Carbon, Merchant Quality, M- Grades |
|
ASTM A 576 REV B |
Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality |
|
ASTM A 578/A 578M |
Standard Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications |
|
ASTM A 580/A 580M |
Standard Specification for Stainless Steel Wire |
|
ASTM A 581/A 581M REV B |
Standard Specification for Free-Machining Stainless Steel Wire and Wire Rods |
|
ASTM A 582/A 582M |
Standard Specification for Free-Machining Stainless Steel Bars |
|
ASTM A 588/A 588M |
Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance- AASHTO No.: M 222 |
|
ASTM A 6/A 6M REV A |
Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling |
|
ASTM A 606 |
Standard Specification for Steel, Sheet and Strip, High-Strength, Low- Alloy, Hot-Rolled and Cold-Rolled, with Improved Atmospheric Corrosion Resistance |
|
ASTM A 615/A 615M REV A |
Standard Specification for Deformed and Plain Carbon Steel Bars for Concrete Reinforcement-AASHTO No.: M 31 |
|
ASTM A 666 |
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar |
|
ASTM A 668/A 668M |
Standard Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use-AASHTO No.: M 102 |
|
ASTM A 681 |
Standard Specification for Tool Steels Alloy |
|
ASTM A 693 |
Standard Specification for Precipitation-Hardening Stainless and Heat- Resisting Steel Plate, Sheet, and Strip |
|
ASTM A 703/A 703M |
Standard Specification for Steel Castings, General Requirements, for Pressure-Containing Parts |
|
ASTM A 706/A 706M REV A |
Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement |
|
ASTM A 733 |
Standard Specification for Welded and Seamless Carbon Steel and Austenitic Stainless Steel Pipe Nipples |
|
ASTM A 743/A 743M |
Standard Specification for Castings, Iron-Chromium, Iron-Chromium- Nickel, Corrosion Resistant, for General Application |
|
ASTM A 744/A 744M |
Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service |
|
ASTM A 751 |
Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products |
|
ASTM A 780 |
Standard Practice for Repair of Damaged and Uncoated Areas of Hot- Dip Galvanized Coatings |
|
ASTM A 788/A 788M REV C |
Standard Specification for Steel Forgings, General Requirements |
|
ASTM A 82/A 82M REV A |
Standard Specification for Steel Wire, Plain, for Concrete Reinforcement- AASHTO Standard AASHTO No. M 32 |
|
ASTM A 829/A 829M |
Standard Specification for Alloy Structural Steel Plates |
|
ASTM A 967 |
Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts |
|
ASTM B 108 REV A |
Standard Specification for Aluminum-Alloy Permanent Mold Castings |
|
ASTM B 111/B 111M |
Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock |
|
ASTM B 117 |
Standard Practice for Operating Salt Spray (Fog) Apparatus |
|
ASTM B 148 |
Standard Specification for Aluminum-Bronze Sand Castings |
|
ASTM B 16/B 16M |
Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines |
|
ASTM B 164 |
Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire |
|
ASTM B 166 |
Standard Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, and N06045)* and Nickel- Chromium-Cobalt- Molybdenum Alloy (UNS N06617) Rod, Bar, and Wire |
|
ASTM B 187/B 187M |
Standard Specification for Copper, Bus Bar, Rod, and Shapes and General Purpose Rod, Bar and Shapes |
|
ASTM B 194 |
Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
|
ASTM B 196/B 196M |
Standard Specification for Copper-Beryllium Alloy Rod and Bar |
|
ASTM B 209 |
Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
|
ASTM B 210 |
Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes |
|
ASTM B 211 |
Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire |
|
ASTM B 221 REV A |
Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
|
ASTM B 241/B 241M |
Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
|
ASTM B 247 REV A |
Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
|
ASTM B 26/B 26M |
Standard Specification for Aluminum-Alloy Sand Castings |
|
ASTM B 265 |
Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate |
|
ASTM B 271 |
Standard Specification for Copper-Base Alloy Centrifugal Castings |
|
ASTM B 308/B 308M |
Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles |
|
ASTM B 32 |
Standard Specification for Solder Metal |
|
ASTM B 338 REV B |
Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers |
|
ASTM B 348 |
Standard Specification for Titanium and Titanium Alloy Bars and Billets |
|
ASTM B 369 |
Standard Specification for Copper-Nickel Alloy Castings |
|
ASTM B 444 |
Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625 and UNS N06852) and Nickel-Chromium-Molybdenum- Silicon Alloy (UNS N06219) Pipe and Tube |
|
ASTM B 446 |
Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel- Chromium-Molybdenum-Tungsten Alloy (UNS N06650)* Rod and Bar |
|
ASTM B 449 |
Standard Specification for Chromates on Aluminum |
|
ASTM B 488 |
Standard Specification for Electrodeposited Coatings of Gold for Engineering Uses |
|
ASTM B 505/B 505M |
Standard Specification for Copper Alloy Continuous Castings |
|
ASTM B 545 |
Standard Specification for Electrodeposited Coatings of Tin |
|
ASTM B 557 REV A |
Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
|
ASTM B 564 |
Standard Specification for Nickel Alloy Forgings |
|
ASTM B 571 |
Standard Practice for Qualitative Adhesion Testing of Metallic Coatings |
|
ASTM B 574 |
Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium- Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod |
|
ASTM B 594 |
Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications |
|
ASTM B 61 |
Standard Specification for Steam or Valve Bronze Castings- Reinstated |
|
ASTM B 62 |
Standard Specification for Composition Bronze or Ounce Metal Castings-(Reinstated) |
|
ASTM B 633 |
Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel |
|
ASTM B 637 |
Standard Specification for Precipitation-Hardening Nickel Alloy Bars, Forgings, and Forging Stock for High-Temperature Service |
|
ASTM B 733 |
Standard Specification for Autocatalytic (Electroless) Nickel- Phosphorus Coatings on Metal |
|
ASTM B 75 |
Standard Specification for Seamless Copper Tube |
|
ASTM B 85 |
Standard Specification for Aluminum-Alloy Die Castings |
|
ASTM B 88 |
Standard Specification for Seamless Copper Water Tube |
|
ASTM C 109/C 109M |
Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) |
|
ASTM C 1107 |
Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink) |
|
ASTM C 136 |
Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
|
ASTM C 143/C 143M REV A |
Standard Test Method for Slump of Hydraulic-Cement Concrete |
|
ASTM C 172 |
Standard Practice for Sampling Freshly Mixed Concrete |
|
ASTM C 177 |
Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
|
ASTM C 231 |
Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
|
ASTM C 297/C 297M |
Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions |
|
ASTM C 31/C 31M REV A |
Standard Practice for Making and Curing Concrete Test Specimens in the Field |
|
ASTM C 33 |
Standard Specification for Concrete Aggregates |
|
ASTM C 39/C 39M |
Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
|
ASTM C 393 |
Standard Test Method for Flexural Properties of Sandwich Constructions |
|
ASTM C 494/C 494M REV A |
Standard Specification for Chemical Admixtures for Concrete |
|
ASTM C 618 |
Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete |
|
ASTM C 76 REV B |
Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
|
ASTM C 94/C 94M |
Standard Specification for Ready-Mixed Concrete |
|
ASTM D 1000 |
Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
|
ASTM D 1002 |
Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) |
|
ASTM D 1056 |
Standard Specification for Flexible Cellular Materials - Sponge or Expanded Rubber |
|
ASTM D 1186 |
Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base |
|
ASTM D 1193 |
Standard Specification for Reagent Water |
|
ASTM D 1238 REV C |
Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
|
ASTM D 1248 |
Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
|
ASTM D 1250 |
Standard Guide for Use of the Petroleum Measurement Tables-API Standard: API MPMS Ch.11.1; IP Designation: 200/04 |
|
ASTM D 1298 |
Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method-API Designation: MPMS Chapter 9.1; IP Designation 160/99 |
|
ASTM D 130 |
Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test-IP Designation: 154/93 |
|
ASTM D 1319 |
Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption-IP Designation: 156/97 |
|
ASTM D 149 REV A |
Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies |
|
ASTM D 1500 REV A |
Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)-IP Designation: 196/97 |
|
ASTM D 1556 |
Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method |
|
ASTM D 1557 |
Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3)) |
|
ASTM D 156 |
Standard Test Method for Saybolt Color of Petroleum Products (Saybolt Chromometer Method) |
|
ASTM D 1654 |
Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
|
ASTM D 1710 |
Standard Specification for Extruded and Compression Molded Polytetrafluoroethylene (PTFE) Rod and Heavy Walled Tubing |
|
ASTM D 1784 |
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
|
ASTM D 1785 |
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 |
|
ASTM D 1876 |
Standard Test Method for Peel Resistance of Adhesives (T-Peel Test) |
|
ASTM D 2000 |
Standard Classification System for Rubber Products in Automotive Applications-SAE J200 |
|
ASTM D 2216 |
Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
|
ASTM D 2240 |
Standard Test Method for Rubber Property-Durometer Hardness |
|
ASTM D 2244 |
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
|
ASTM D 2487 |
Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
|
ASTM D 2488 |
Standard Practice for Description and Identification of Soils (Visual- Manual Procedure) |
|
ASTM D 2500 |
Standard Test Method for Cloud Point of Petroleum Products-British Standard 4458; IP Designation: 219/82 |
|
ASTM D 256 REV A |
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
|
ASTM D 257 |
Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
|
ASTM D 2622 |
Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
|
ASTM D 2887 REV A |
Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography-IP Designation: 406 |
|
ASTM D 2922 |
Standard Test Methods for Density of Soil and Soil-Aggregate in Place by Nuclear Methods (Shallow Depth) |
|
ASTM D 3227 REV A |
Standard Test Method for (Thiol Mercaptan) Sulfur in Gasoline, Kerosine, Aviation Turbine, and Distillate Fuels (Potentiometric Method)-IP Designation 342/00 |
|
ASTM D 323 REV A |
Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method) |
|
ASTM D 3241 REV B |
Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedure)-IP Designation: 323/99 |
|
ASTM D 3295 |
Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
|
ASTM D 3330/D 3330M |
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape |
|
ASTM D 3363 |
Standard Test Method for Film Hardness by Pencil Test |
|
ASTM D 3574 |
Standard Test Methods for Flexible Cellular MaterialsSlab, Bonded, and Molded Urethane Foams |
|
ASTM D 381 |
Standard Test Method for Gum Content in Fuels by Jet Evaporation-IP Designation: 131/99 |
|
ASTM D 3935 |
Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
|
ASTM D 395 |
Standard Test Methods for Rubber PropertyCompression Set |
|
ASTM D 3951 |
Standard Practice for Commercial Packaging |
|
ASTM D 396 |
Standard Specification for Fuel Oils |
|
ASTM D 4000 |
Standard Classification System for Specifying Plastic Materials |
|
ASTM D 4052 |
Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter-X´A6´hNX´A6´hM IP Designation: 365/84(86) |
|
ASTM D 4057 |
Standard Practice for Manual Sampling of Petroleum and Petroleum Products-IP Designation: IMPMS (Chapter 8.1) |
|
ASTM D 4066 REV A |
Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
|
ASTM D 412 REV A |
Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers Tension |
|
ASTM D 4169 |
Standard Practice for Performance Testing of Shipping Containers and Systems |
|
ASTM D 4176 |
Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
|
ASTM D 4181 |
Standard Classification for Acetal (POM) Molding and Extrusion Materials |
|
ASTM D 422 |
Standard Test Method for Particle-Size Analysis of Soils |
|
ASTM D 4294 |
Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry |
|
ASTM D 4318 |
Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
|
ASTM D 445 |
Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity)-IP Designation: 71/1/97; British Standard 2000: Part 71:1990 |
|
ASTM D 471 |
Standard Test Method for Rubber PropertyEffect of Liquids |
|
ASTM D 4814 REV B |
Standard Specification for Automotive Spark-Ignition Engine Fuel |
|
ASTM D 5034 |
Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test) |
|
ASTM D 5118/D 5118M REV A |
Standard Practice for Fabrication of Fiberboard Shipping Boxes |
|
ASTM D 5191 REV A |
Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
|
ASTM D 523 |
Standard Test Method for Specular Gloss |
|
ASTM D 5363 |
Standard Specification for Anaerobic Single-Component Adhesives (AN) |
|
ASTM D 5486/D 5486M |
Standard Specification for Pressure-Sensitive Tape for Packaging, Box Closure, and Sealing |
|
ASTM D 56 |
Standard Test Method for Flash Point by Tag Closed Cup Tester |
|
ASTM D 570 |
Standard Test Method for Water Absorption of Plastics |
|
ASTM D 573 |
Standard Test Method for RubberDeterioration in an Air Oven |
|
ASTM D 5948 |
Standard Specification for Molding Compounds, Thermosetting |
|
ASTM D 610 |
Standard Test Method for Evaluating Degree of Rusting on Painted Steel Surfaces-SSPC-VIS-2 |
|
ASTM D 613 |
Standard Test Method for Cetane Number of Diesel Fuel Oil-IP Designation: 41/2000 |
|
ASTM D 618 |
Standard Practice for Conditioning Plastics for Testing |
|
ASTM D 6193 |
Standard Practice for Stitches and Seams |
|
ASTM D 624 |
Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers |
|
ASTM D 638 |
Standard Test Method for Tensile Properties of Plastics |
|
ASTM D 648 |
Standard Test Method for Deflection Temperature of Plastics under Flexural Load in the Edgewise Position |
|
ASTM D 6576 |
Standard Specification for Flexible Cellular Rubber Chemically Blown |
|
ASTM D 695 REV A |
Standard Test Method for Compressive Properties of Rigid Plastics |
|
ASTM D 698 REV A |
Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3)) |
|
ASTM D 709 |
Standard Specification for Laminated Thermosetting Materials |
|
ASTM D 714 |
Standard Test Method for Evaluating Degree of Blistering of Paints |
|
ASTM D 740 |
Standard Specification for Methyl Ethyl Ketone |
|
ASTM D 790 |
Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
|
ASTM D 792 |
Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
|
ASTM D 86 |
Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure |
|
ASTM D 882 |
Standard Test Method for Tensile Properties of Thin Plastic Sheeting |
|
ASTM D 903 |
Standard Test Method for Peel or Stripping Strength of Adhesive Bonds |
|
ASTM D 92 REV A |
Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester-IP Designation: 36/84 (89); AASHTO No.: T48; DIN 51 376 |
|
ASTM D 93 REV A |
Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester-IP Designation: 34/99 |
|
ASTM D 95 |
Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation-AASHTO No. T55; API Designation: MPMS Chapter 10.5; IP Designation: 74/82(88) |
|
ASTM D 97 REV A |
Standard Test Method for Pour Point of Petroleum Products-IP Designation: 15/95 |
|
ASTM D 974 |
Standard Test Method for Acid and Base Number by Color-Indicator Titration-IP Designation: 139/98 |
|
ASTM D 975 |
Standard Specification for Diesel Fuel Oils |
|
ASTM D 976 REV B |
Standard Test Method for Calculated Cetane Index of Distillate Fuels |
|
ASTM E 10 |
Standard Test Method for Brinell Hardness of Metallic Materials-AASHTO No. T70-86 |
|
ASTM E 11 |
Standard Specification for Wire Cloth and Sieves for Testing Purposes |
|
ASTM E 112 |
Standard Test Methods for Determining Average Grain Size |
|
ASTM E 119 REV A |
Standard Test Methods for Fire Tests of Building Construction and Materials |
|
ASTM E 140 |
Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, and Scleroscope Hardness |
|
ASTM E 1417 |
Standard Practice for Liquid Penetrant Testing |
|
ASTM E 1444 |
Standard Practice for Magnetic Particle Testing |
|
ASTM E 155 |
Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings |
|
ASTM E 1742 |
Standard Practice for Radiographic Examination |
|
ASTM E 18 |
Standard Test Methods for Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials |
|
ASTM E 23 |
Standard Test Methods for Notched Bar Impact Testing of Metallic Materials |
|
ASTM E 29 |
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
|
ASTM E 3 |
Standard Practice for Preparation of Metallographic Specimens |
|
ASTM E 384 REV A |
Standard Test Method for Microindentation Hardness of Materials |
|
ASTM E 399 |
Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness KIc of Metallic Materials |
|
ASTM E 4 |
Standard Practices for Force Verification of Testing Machines-AASHTO No: T67 |
|
ASTM E 446 |
Standard Reference Radiographs for Steel Castings up to 2 in. (51 mm) in Thickness |
|
ASTM E 45 |
Standard Test Methods for Determining the Inclusion Content of Steel |
|
ASTM E 527 |
Standard Practice for Numbering Metals and Alloys (UNS) |
|
ASTM E 595 |
Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment |
|
ASTM E 709 |
Standard Guide for Magnetic Particle Examination |
|
ASTM E 8 |
Standard Test Methods for Tension Testing of Metallic Materials-AASHTO No.: T68 |
|
ASTM E 84 |
Standard Test Method for Surface Burning Characteristics of Building Materials |
|
ASTM E 8M |
Standard Test Methods for Tension Testing of Metallic Materials (METRIC) |
|
ASTM E 92 |
Standard Test Method for Vickers Hardness of Metallic Materials |
|
ASTM E 96/E 96M |
Standard Test Methods for Water Vapor Transmission of Materials |
|
ASTM F 104 |
Standard Classification System for Nonmetallic Gasket Materials |
|
ASTM F 1166 REV A |
Standard Practice for Human Engineering Design for Marine Systems, Equipment and Facilities |
|
ASTM F 436 |
Standard Specification for Hardened Steel Washers |
|
ASTM F 468 REV A |
Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use |
|
ASTM F 519 |
Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating Processes and Service Environments |
|
ASTM F 593 |
Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
|
ASTM F 594 |
Standard Specification for Stainless Steel Nuts |
|
ASTM F 606 |
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets |
|
ASTM F 835 |
Standard Specification for Alloy Steel Socket Button and Flat Countersunk Head Cap Screws |
|
ASTM F 879 REV A |
Standard Specification for Stainless Steel Socket Button and Flat Countersunk Head Cap Screws |
|
ASTM G 85 |
Standard Practice for Modified Salt Spray (Fog) Testing |